Hoot Aerobic System Alarm: What the Control Panel Lights Mean

Written by

· Published

·

Illustration of an aerobic septic control panel with green, red and amber indicator lights next to an air pump cover

A Hoot control panel uses its lights to say whether the system is normal, has a water level problem, or has an aeration problem. This guide explains what each light condition means and what an owner can safely check before calling for service.

It is based on Hoot Systems’ own Panel Trouble Shooting Guide, which is written for service technicians. The owner-level steps here are limited to things you can do without opening the panel or a tank. Hoot has made several panel versions, so confirm against the label and manual for yours.

What the lights mean

What you see What Hoot’s guide says
Steady green System OK. The controller sees all functions in normal operation.
Steady red System alarm. It occurs only with a water level problem or an aeration problem, and that light will be on too.
Water level light Water has been over the alarm probe for more than 30 continuous seconds. The light turns off when the water drops.
Aeration light The controller is not seeing enough air pressure from the blower.
Fast flashing red The system is connected to 220 volts instead of 110. This is a wiring fault. Power should be disconnected immediately and a professional called.
Flashing red on older five-light panels The 9 volt backup battery is not in place. This applies to certain older software versions only.
No lights at all The panel is not getting power.

Water level alarm

This means the pump tank is fuller than it should be, usually because water is not being pumped out to the spray or drip area. Hoot’s guide lists these causes for technicians to work through:

  • The 20 amp circuit breaker for the water pump has tripped.
  • A relay in the panel is not working.
  • The effluent pump is clogged.
  • The check valve on top of the pump is stuck.
  • The discharge line is restricted, clogged or frozen.

What you can do: cut water use right away. Check whether the pump breaker has tripped and reset it once. If it trips again, leave it off and call for service. Look at the spray area: are the heads coming up, and is one area flooded? In freezing weather, see aerobic septic systems in freezing weather.

The light should go out on its own once the water level drops below the probe. If it stays on after a few hours of low water use, the system needs service.

Aeration alarm

This means the controller is not sensing enough pressure from the blower. Hoot’s guide gives these reasons:

  • The blower is not running.
  • There is a leak, a kink or, in winter, ice in the small sensor hose between the blower and the panel.
  • The tank was recently pumped out and has not refilled yet.
  • There is a break in the aeration plumbing.
  • The blower needs to be rebuilt, typically after three to five years of operation.
  • Grass, leaves, mud or mulch around or under the blower is making it overheat and shut down.

What you can do: listen for the blower. Clear grass clippings, leaves and mulch from around it. Hoot’s guide says the blower must sit on a raised pad with debris cleared away. If the tank was pumped in the last day or two, tell the technician, because that alone can cause this alarm until the tank refills.

For the repair-or-replace decision on the blower itself, see aerobic septic air pump not working.

No lights

The panel has no power. Hoot’s guide starts with two checks an owner can make: the disconnect switch near the panel and the breaker in the house. If both are on and the panel is still dark, the guide’s next step is to have an electrician restore power to the panel.

The guide also notes that a lightning strike or electrical surge can damage the panel’s transformer and control board. If the panel went dark after a storm, say so when you call.

Green light, but something is clearly wrong

If the panel shows green while water is running out of the tank or the yard is flooded, the guide points to a connection, grounding or stray voltage problem that is stopping the panel from seeing the fault. It lists possible sources of stray voltage including pool equipment, an air conditioner, and electric fences, both the dog type and livestock type. Mention any of these near your system. This is technician work.

What not to do

  • Do not open the control panel or a tank.
  • Do not run the panel from a generator unless your provider has told you how. Hoot’s guide warns technicians not to run the controller from a generator without a load on it.
  • Do not keep resetting a breaker that trips again.
  • Do not ignore a red light because the yard looks fine.

What to tell the technician

  • Which lights are on, and whether red is steady or flashing.
  • Whether the blower is running.
  • Whether the sprinklers have been operating.
  • Recent events: storm, power outage, freeze, tank pumping, heavy water use, yard work near the blower or sensor hose.
  • Anything electrical installed nearby recently.

Related guides

Sources

General homeowner education only. This is an independent guide and is not affiliated with Hoot Systems. Your own manual and your service provider control the correct procedure for your installation.

Last reviewed: November 10, 2026.

About this guide

Alex González researches and reviews every guide on Aerobic Septic Owner using primary sources such as government guidance, university extension resources, manufacturer documentation, and published service information. General guidance is kept separate from model-specific instructions and local requirements.

Learn more about Alex González and this site, or read the complete Editorial Policy. If you spot an error or outdated source, please send a correction.

Educational information only. Your permit, system manual, local authority, and qualified service provider determine the correct procedure for your installation.